How can I fix the issues with my Arlo login?

Most of the time, Arlo login issues are the result of incorrect configurations. So, if you are looking to fix the errors, you have to fix the configurations on your Arlo camera. In this guide, we'll try to cover all the basic to essential configurations for the Arlo camera to fix the issues. Furthermore, we are also going to discuss some general troubleshooting tips to help you fix the errors with your Arlo camera setup. 

 

Troubleshooting the issues with the Arlo login- 

The first and the foremost step to fix the issues with your Arlo camera is to connect it to a good internet connection. So, make sure to connect the camera to a strong internet connection. Also, ensure only to use the private network to connect your Arlo camera. 

 

Here are the reasons and their solutions-

 

1. Incorrect installation- 

If you haven't set up your Arlo camera properly, you are most likely to face login issues. So, to fix those annoying login issues, first, you have to make sure to install your Arlo camera properly. 

You can follow these instructions to install your Arlo camera- 

 

2. Install the Base Station- 

• Connect the Arlo Base station to your ISP modem or router using an ethernet cable. 
• To do the following, insert one end of the ethernet cable into the LAN port of the Base station and another end of the cable into the LAN port of your modem or router. 
• Next, connect your Arlo Base station to the power supply and press the power button on it. After that, wait for the Power LED on the Base Station to turn on green. 

3. Registration- 

• Open a laptop or mobile device, go to arlo.com and click on the 'New Setup' option. 
• After that, fill in all the details and hit the Next button. 
• Now, enter the serial number of your Arlo Base station.
• And hit the Continue button. 

 

4.  Sync the Arlo camera on the Base Station- 

• Firstly, bring the Arlo camera into the range of the Base station. 
• After that, hold the Sync button on the base station for almost 2 to 3 seconds. 
• Similarly, press the Sync button on your Arlo camera for two to three seconds and then release it. 
• Check the Camera LED on the Arlo base station. If it is blinking green, the Arlo camera and base station has successfully synced. 
• After you successfully Sync the Arlo camera and Base station, you are done with the installation of the camera. 

 

5. Incompatible browser- 

 

If you use an incompatible browser to connect your login to your Arlo camera, login issues can occur. Outdated browsers are not supported with the Arlo cameras. So, make sure to use an updated version of the browser you use, or you can also consider switching the browser to a new one. Also, delete the browser cookies and cache memory to fix the issue.

 

6. Firewall Restrictions- 

The firewall on the system can also prevent you from accessing the Arlo camera. So, you can disable it and then try to log in to your camera. 

 

7. Incorrect login details- 

Make sure to use the correct login details for your Arlo camera. First, confirm the login details and then try to login in again to your Arlo camera system. 

 

8. Power cycling-

 You can also try the power cycle of your Arlo camera to fix the issue. To do so, first power off your Arlo camera, and after that, wait for some time. Now, power it on again and sync to the Base station. Once done, try to log in again to your device. 

 

9. Inadequate power supply –

If your Arlo base station is not receiving an adequate power supply then, it can result in login issues. If you see issues with the Power supply, then disconnect the Arlo base station. And then, connect it again.

 

10. Check the device you use to log in-

 Also, don't forget to check the device you use to log in. Ensure that your mobile or laptop device is connected to a network connection. 

 

If the above solutions don't work for you, you could try to factory reset your Arlo Base station and then connect the Arlo camera to the base station. 

 

Reset the Arlo Base Station-

• Firstly, find the reset button on your Arlo Base station. For identification, it is always labeled as RESET.
• Now, hold the reset button for almost 20 to 30 seconds and release it. To hold it, you can use any paper clip, sim injector, or pointy object. 
• Here, Base Station starts itself to apply the changes. 
• After the Base station starts, connect your Arlo camera to the Base Station and then try to log in to your camera. 

 

Contact the Netgear customer support-

 The ultimate way to fix any issues is to contact customer support. To find the support for your Arlo camera, you have to get in touch with Netgear customer support here https://www.arlocamerasystem.com/. 

 

Conclusion- 

 To troubleshoot the issues with your Arlo camera, you can try all the provided solutions in this guide. Lastly, we just guide has helped you with your Arlo camera Login.